Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 41

Page: 41 / 216

SPEEDOMETER

401912-01

–

Wait for 5 seconds.

The speedometer changes to the next menu item. The clock

symbol flashes.

Resetting the time

–

Press the left button.

The value decreases.

Advancing the time

–

Press the right button.

The value increases.

7.7

Setting the service display

Condition

The motorcycle is stationary.

401913-01

–

Press both buttons for 3

–

5 seconds.

The Setup menu is displayed. The

UNIT

display flashes.

–

Wait for the menu of the service display

to flash.

–

Set the service.
Guideline

Service display switched off

Shortening the service interval

–

Press the left button.

The value decreases.

Extending the service interval

–

Press the right button.

The value increases.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands