Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 70

Page: 70 / 216

11 TUNING THE CHASSIS

Info

The effect of the high-speed setting can be seen in fast compression of the shock absorber.

V00494-11

–

Turn adjusting screw



all the way clockwise with a socket wrench.

Info

Do not loosen fitting



–

Turn counterclockwise by the number of turns corresponding to the shock absorber

type.
Guideline

Compression damping, high-speed

Standard

1.5 turns

Info

Turn clockwise to increase damping; turn counterclockwise to reduce damp-

ing.

11.7

Adjusting the rebound damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will fly off if the shock absorber is disassembled incorrectly.

The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands