Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 181

Page: 181 / 216

19 CLEANING, CARE

179

401060-01

–

Clean the motorcycle. (

p. 176)

–

Clean the brake system.

Info

After

EVERY

trip on salted roads, thoroughly wash the brake calipers and

brake linings with cold water and dry carefully. This should be done after the

parts are cooled down and while they are installed.
After use on salted roads, clean the motorcycle thoroughly with cold water and

dry it properly.

–

Treat the engine, the swingarm, and all other bare or galvanized parts (except brake

discs) with a wax-based anti-corrosion substance.

Info

To prevent serious reduction of the braking efficiency, make sure no

anti-corrosion substance gets on to the brake discs.

–

Clean the chain. (

p. 88)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands