Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 69

Page: 69 / 216

11 TUNING THE CHASSIS

Info

The effect of the low-speed setting can be seen in slow to normal compression of the shock absorber.

V00494-10

–

Turn adjusting screw



clockwise with a screwdriver up to the last perceptible click.

Info

Do not loosen fitting



–

Turn counterclockwise by the number of clicks corresponding to the shock absorber

type.
Guideline

Compression damping, low-speed

Standard

15 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce damp-

ing.

11.6

Adjusting the high-speed compression damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will fly off if the shock absorber is disassembled incorrectly.

The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands