Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 96

Page: 96 / 216

12 SERVICE WORK ON THE CHASSIS

1 2 3

16 17 18

400987-10

–

Pull at the top part of the chain with the specified weight



Guideline

Weight of chain wear measurement

15 kg (33 lb.)

–

Measure distance



of 18 chain rollers in the lower chain section.

Info

Chain wear is not always even, so you should repeat this measurement at dif-

ferent chain positions.

Maximum distance



at the longest

chain section

272 mm (10.71 in)

» If the distance



is greater than the specified measurement:

–

Change the drivetrain kit.

Info

When the chain is replaced, the rear sprocket and engine sprocket

should also be changed.
New chains wear out faster on an old, worn rear sprocket or engine

sprocket.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands