Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 112

Page: 112 / 216

13 BRAKE SYSTEM

110

K00407-10

–

Check the brake linings for minimum thickness



Minimum thickness



≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the front brake linings.

(

p. 110)

–

Check the brake linings for damage and cracking.
» If there is wear or tearing:

–

Change the front brake linings.

(

p. 110)

13.7

Changing the front brake linings

Warning

Danger of accidents

Incorrect maintenance will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna Motorcycles workshop will

be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands