Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 78

Page: 78 / 216

11 TUNING THE CHASSIS

V00496-10

–

Remove screws



. Take off the handlebar clamps. Remove the handlebar and lay it

to one side.

Info

Cover the components to protect them against damage.
Do not kink the cables and lines.

–

Remove screws



. Remove handlebar support



–

Position rubber bushings



and push through nuts



from below.

–

Place the handlebar support in the required position. Mount and tighten screws



Guideline

Screw, handlebar support

M10

45 Nm

(33.2 lbf ft)

Loctite

243™

–

Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–

Position the handlebar clamps.

–

Mount screws



, but do not tighten yet.

–

Screw the handlebar clamps so that both parts touch at the front and tighten all of the

screws.
Guideline

Screw, handlebar clamp

20 Nm (14.8 lbf ft)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands