Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 150

Page: 150 / 216

15 ELECTRICAL SYSTEM

148

Warning

Fire hazard

Incorrect fuses overload the electrical system.

–

Only use fuses with the required ampere value.

–

Do not bypass or repair fuses.

–

Use spare fuses with the correct rating only.

Fuse (75011088010) (

p. 192)

Fuse (75011088015) (

p. 192)

Tip

Replace the spare fuse in the fuse box so that it is available if needed.

–

Check that the power consumer is functioning properly.

–

Close the fuse box cover.

Finishing work

–

Mount the seat. (

p. 83)

15.7

Removing the headlight mask with the headlight

Preparatory work

–

Switch off the ignition by turning the ignition key to the

OFF

position.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands