Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 42

Page: 42 / 216

SPEEDOMETER

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears on the display.

7.8

Speed, time, and DST distance 1

401901-01

–

Press one of the buttons until

DST

appears on the speedometer.

KM/H

M/H

shows the speed.

shows the time.

DST

shows the distance since the last reset, such as between two refueling stops.

Info

If the value of 39999.9 is exceeded,

DST

is automatically reset to 0.0.

Press the left button

briefly.

Next display mode

Press the left button

for 3

–

5 seconds.

DST

can be preset to a value between 0.0 and 39999.9 by

pressing the buttons.

Press the right but-

ton briefly.

Next display mode

Press the right but-

ton for 3

–

5 sec-

onds.

DST

is reset to 0.0.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands