Huawei UPS5000-H-400 kVA User Manual Download Page 50

Page: 50 / 175

Table 4-12 Indicator status

Status

Color

Meaning

Red

A critical alarm has been generated, and the buzzer

sounds continuously.

Yellow

A minor alarm has been generated, and the buzzer

buzzes intermittently at 2 Hz.

Green

The UPS is running properly or a warning has been

generated.

Off

The MDU is powered off.

NO TE

The indicator on the MDU panel is yellow when the bypass supplies power in non-ECO

mode.

Figure 4-15 MDU ports

Table 4-13 MDU port description

No.

Port

Name

Description

MUS05A

(DB26)

Connects to the MDU and monitoring interface card.

Network port

CAN

Reserved

RS485_1

Reserved

FE_1

Reserved

FE_2

Reserved

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands