Huawei UPS5000-H-400 kVA User Manual Download Page 39

Page: 39 / 175

Indicator

Color

Status

Description

Off

The bypass software is being

upgraded.

Alarm

indicator

Yellow Steady on

A minor alarm is generated for the

bypass.

Off

There is no minor alarm for the

bypass, or the software is being

upgraded.

Fault

indicator

Red

Steady on

A critical alarm is generated for the

bypass.

Off

There is no critical alarm for the

bypass, or the software is being

upgraded.

Table 4-4 Specifications

Item

Specifications

Dimensions (H x W x D) ● 400–600 kVA: 200 mm x 600 mm x 600 mm

● 800 kVA: 500 mm x 480 mm x 550 mm

Weight

● 400–600 kVA: ≤ 50 kg
● 800 kVA: ≤ 83 kg

4.3 Control Module

4.3.1 Overview

The control module in a standard configuration contains two ECMs, one dry

contact card, and one monitoring interface card from left to right. The four cards

are hot-swappable. One subrack is reserved above the dry contact card. A

backfeed protection card or dry contact extended card can be inserted into the

subrack.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands