Huawei UPS5000-H-400 kVA User Manual Download Page 30

Page: 30 / 175

Figure 2-7 UPS conceptual diagram in battery mode

2.5.4 ECO Mode

The economic control operation (ECO) mode is an economical working mode,

which can be configured on the LCD or web user interface (WebUI). In ECO mode,

when the bypass input is within the ECO voltage and frequency ranges and other

ECO power supply conditions are met, the UPS works in bypass mode and the

inverter is in standby state. When the bypass source voltage is outside the ECO

voltage range, the UPS transfers from bypass mode to inverter mode. In bypass

mode or inverter mode, the rectifier keeps working and charges batteries using a

charger. The ECO mode delivers a high efficiency.

Figure 2-8 UPS conceptual diagram in ECO mode

NO TE

Manual startup is required to ensure that the inverter is in standby state and the power

flow has reached the inverter.

2.5.5 Source-Share Mode

If the UPS works properly and the AC input power of rectifiers is insufficient, the

UPS transfers to source-share mode. In this case, the power module obtains

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

2 Product Overview

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands