Huawei UPS5000-H-400 kVA User Manual Download Page 46

Page: 46 / 175

Port

Silk

Screen

Description

COM

overload, Battery temp. abnormal, and

Battery EOD.

● Configure power segment settings based on

backup time.

DB26

MDU

Supports FE, RS485, I2C, CAN, and other signals.

Battery

temperature

sensor port

B_TEMP

Connects to an indoor battery temperature

sensor.

Southbound

communicatio

ns port 1

COM1

● Supported protocol: Modbus-RTU
● Connects to an ambient temperature and

humidity sensor over two wires.

Southbound

communicatio

ns port 2

COM2

● Supported protocol: Modbus-RTU
● Connects to a southbound device.

Network port

● Supported protocols: Modbus-TCP, HTTPS, and

SNMP

● Connects to the network port on a PC.
● Network port for connecting to the web

service and for SNMP networking

Northbound

communicatio

ns port

RS485

● Supported protocol: Modbus-RTU
● Connects to a northbound network

management device or third-party network

management device over two wires.

NO TE

● Signal cables must be double-insulated twisted cables. If the cable length is within 25–

50 m, the cross-sectional area must be 0.5–1.5 mm

● RS485 cables and FE cables must be shielded cables.

Figure 4-9

and

Figure 4-10

are recommended wiring methods for DO ports.

Figure 4-9 Wiring method 1

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands