Huawei UPS5000-H-400 kVA User Manual Download Page 41

Page: 41 / 175

Table 4-5 Port description

Silk Screen

Description

PARALLEL

The PARALLEL port transmits parallel signals between racks.

BSC

The BSC port is used in a dual-bus system to synchronize

output frequencies and phases between UPS systems,

ensuring that two buses can switch with each other.
BSC cables are hot-swappable.

NO TE

No parallel cable is required for a single UPS.

Table 4-6 Indicator description

Indicator Color

Status

Description

NORMAL Green

Steady on

This ECM is the active ECM.

Blinking at 0.5

This ECM is the standby ECM and it is

ready.

Off

This ECM is not ready or the software

of this ECM is being upgraded.

Blinking at 4 Hz

The ECM software is being upgraded

or not configured.

ALM

Yellow

Steady on

The ECM has a minor alarm, but it

does not need to be replaced.

Off

The ECM has no minor alarm or the

software of the ECM is being

upgraded.

FAULT

Red

Steady on

The ECM has a critical alarm.

Off

The ECM has no critical alarm or the

software of the ECM is being

upgraded.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands