Huawei UPS5000-H-400 kVA User Manual Download Page 148

Page: 148 / 175

Item

Setting

Description

Requisite UPSs

Sets it based on

the actual

number of UPSs.

In a parallel system, the two

parameters must be set to the same

values for all UPSs.

Redundant

UPSs

Sets it based on

the actual

number of UPSs.

2. Battery Settings: On the LCD, choose System Info > Settings > Battery

Settings. On the WebUI, choose Monitoring > Battery System > Running

Parameter > Battery Settings.

Table 8-6 Battery Settings

Item

Setting

Battery string sharing

Set this parameter as required.

NO TE

The system may generate alarms such as Rack quantity mismatch, Insufficient

redundant racks, and Inter-rack par. cable alarm. The alarms are automatically cleared 1

minute after you connect all parallel cables.

Step 6 Turn off the mains and bypass input switches for the new UPS.
Step 7 Connect an inter-rack parallel cable for the new UPS.

NO TE

● The length of the parallel cable between two UPSs depends on the onsite environment.
● Route cables between the two UPSs through the busway between racks. If there is no

busway, route the cables along the routes of the EPO, ECC800, and dry contact signal

cables.

● If two racks are far away from each other, prepare a longer parallel cable.

Step 8 Power on the new UPS. For details, see

7.1.1 Powering On the UPS

Step 9 If the Inconsistent parallel param. alarm is generated, choose System Info >

Settings on the LCD of the original system and tap Parameter Sync to

synchronize parameters between UPSs in the parallel system.

Step 10 If the PDC output breaker open alarm is generated in the system, choose System

Info > Alarms on the LCD and tap Clear Faults to clear the alarm.

Step 11 Turn on the external output switch of the new UPS to connect the UPS to the

parallel system. The new UPS has no output.

Step 12 If there are multiple new UPSs, repeat the preceding steps to add the UPSs to the

parallel system.

Step 13 Turn on the battery switches for the new UPSs (if there are multiple battery

strings, turn on the switch for each battery string and then the general switch

between battery strings and the UPSs).

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

8 Parallel System Commissioning

Issue 02 (2021-04-22)

140

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands