Huawei UPS5000-H-400 kVA User Manual Download Page 104

Page: 104 / 175

Figure 6-52 Installing cables

Step 4 Connect signal cables. Bind cables to the cabinet nearby.

●

If you need to log in to the WebUI of the UPS monitoring system, connect the

network port on a PC to the FE port on the monitoring interface card.

●

If the UPS needs to connect to an external network management device,

connect the external network management device to the RS485 port on the

monitoring interface card.

NO TICE

– Do not bind signal cables and power cables together.
– RS485 cables and FE cables must be shielded cables.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

6 Installation

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands