Huawei UPS5000-H-400 kVA User Manual Download Page 36

Page: 36 / 175

Component Description

4.1 Power Module

The power module consists of a power factor correction (PFC) rectifier and

inverter. It performs AC/DC or DC/DC conversion on the mains and battery inputs,

and stabilizes the bus voltage. The inverter (DC/AC) converts the inputs into sine

wave outputs.

Figure 4-1 Appearance

(1) Handle

(2) Positioning lock

(3) Running indicator (4) Alarm indicator

(5) Fault indicator

(6) Ready switch

(7) Output ports

(8) Input ports

Table 4-1 Indicator description

Indicator Color

Status

Description

Running

indicator

Green

Steady

The system is working in inverter mode.

Blinking

at long

intervals

● The inverter is ready and in standby state

(blinking at 0.5 Hz, on for 1s and off for 1s).

● The inverter is not started (blinking at 0.2

Hz, on for 2.5s and off for 2.5s).

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Summary of Contents for UPS5000-H-400 kVA
















































































































































































Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands

Huawei UPS5000-H-400 kVA, User Manual

Search results

Summary of Contents for UPS5000-H-400 kVA

Reviews:

Related manuals for UPS5000-H-400 kVA

Brands by name

Popular brands