manualshive.com logo in svg

HP StoreEver MSL3040, User'S And Service Manual

The HP StoreEver MSL3040 is a high-performance tape library designed for data storage and backup needs. Unlock the full potential of this product by downloading the free User's and Service Manual from our website, providing you with detailed instructions and information.

Share
Download
background image

Event
code

Message and description

Details and solution

4020

Database has been reset due to a problem
that prevented the library from powering up.

Restore previously saved configuration data.
If you do not have a saved configuration file,
reconfigure the library.

4021

Drive has been hot removed while in active
status as data transfer device.

Drives must be powered off before removing
them from the library. Reinsert the removed
drive in the same position from which it was
removed.

4022

A full-height drive in incorrect boundary
location.

A full-height drive will only operate in the
bottom pair of drive bays. Reinstall the tape
drive in the proper location.

4023

Drive not cabled (ports not linked up).

The tape drive must have an FC or SAS
cable attached to transfer data and
communicate with host applications.

4024

One or two unit position transmitter/detector
failures.

Ensure that the library has the latest
firmware installed.

4025

Library test failed due to a cartridge error.

1.

Remove the cartridge and inspect it for
damage.

2.

Retry the operation with another
cartridge.

4026

Unlabeled media detected in library.

Previous versions of library firmware do not
support use of unlabeled media.

To use unlabeled media, update the library
firmware to the latest released version and
then enable detection of unlabeled media
from the RMI.

4028

Drive cannot use this media due to it being
an unknown or unsupported format.
Possibly the media is the wrong generation
of media.

1.

Verify that the LTO generation on the
barcode label media ID matches the LTO
generation of the data cartridge.

2.

Remove cartridges that are incompatible
with the drives in the library.

4029

Incompatible media move operation blocked
by media barcode ID check.

Verify that the LTO generation on the media
barcode label matches the LTO generation
of the data cartridge. Replace the label if it is
incorrect or remove the incompatible
cartridge from the library.

Table Continued

Event codes

219

Summary of Contents for StoreEver MSL3040





















































































































































































































































Reviews:

No comments

Related manuals for StoreEver MSL3040

LaCie Mobile Disk Quick Install Manual preview
Mobile Disk
Brand: LaCie Pages: 22
WATSON SEVEN Assembly Instructions Manual preview
SEVEN
Brand: WATSON Pages: 12
Western Digital WDBAAE3200ASL - My Passport Studio Specifications preview
WDBAAE3200ASL - My Passport Studio
Brand: Western Digital Pages: 2
YardCraft Fairmont Garden Shed Assembly Instructions Manual preview
Fairmont Garden Shed
Brand: YardCraft Pages: 29
Y-E Data YD-380 Maintenance Manual preview
YD-380
Brand: Y-E Data Pages: 48
Compaq 175195-B21 Reference Manual preview
175195-B21
Brand: Compaq Pages: 139
garofalo V06.01.002 User Manual preview
V06.01.002
Brand: garofalo Pages: 12
Eaton Cutler Hammer SRAM PC104 Instruction Manual preview
Cutler Hammer SRAM PC104
Brand: Eaton Pages: 2
Buffalo HD-HCU2 DriveStation User Manual preview
HD-HCU2 DriveStation
Brand: Buffalo Pages: 8
Symantec FileStore N8300 Product Description Manual preview
FileStore N8300
Brand: Symantec Pages: 55
Husky HBR652454W3 Use And Care Manual preview
HBR652454W3
Brand: Husky Pages: 4
Verbatim QUAD INTERFACE Quick Start Manual preview
QUAD INTERFACE
Brand: Verbatim Pages: 53
ClearSpan 108294F Manual preview
108294F
Brand: ClearSpan Pages: 25
OLT SM812-FJ-Ply Assembly Manual preview
SM812-FJ-Ply
Brand: OLT Pages: 43
Sunex Monster Mobile Owner'S Manual preview
Monster Mobile
Brand: Sunex Pages: 13
ABSCO SHEDS 45302WK Assembly & Instruction Manual preview
45302WK
Brand: ABSCO SHEDS Pages: 38
Absco 45302WK Manual preview
45302WK
Brand: Absco Pages: 43
HddSurgery Seagate 7200.10 Manual preview
Seagate 7200.10
Brand: HddSurgery Pages: 27

Brands by name

Popular brands

Load more brands