manualshive.com logo in svg

HP E4401B, Programmer'S Manual

Share
Download
HP E4401B Programmer'S Manual Download Page 17

Chapter 1

1-3

Programming Fundamentals

Creating Valid Commands

Creating Valid Commands

Commands are not case sensitive and there are often many different
ways of writing a particular command. These are examples of valid
commands for a given command syntax:

Command Syntax

Sample Valid Commands

[:SENSe]:BANDwidth[:RESolution]

<freq>

The following sample commands are all
identical. They will all cause the same result.

•

:Sense:Band:Res 1700

•

:BANDWIDTH:RESOLUTION 1.7e3

•

:sens:band 1.7KHZ

•

:SENS:band 1.7E3Hz

•

:band 1.7kHz

•

:bandwidth:RES 1.7e3Hz

:MEASure:HARMonics:AMPLitude[n?

The last command below returns different
results than the commands above it. The
number 3 in the command causes this. See the
command description for more information.

•

:MEAS:HARM:AMPL?

•

:Meas:Harm:Ampl?

•

:MEAS:HARM:AMPL3?

[:SENSe]:DETector[:FUNCtion]
NEGative|POSitive|SAMPle

•

DET:FUNC NEG

•

:Sense:Detector:Function Sample

:INITiate:CONTinuous OFF|ON|0|1

The sample commands below are identical.

•

:INIT:CONT ON

•

:init:continuous 1

Summary of Contents for E4401B















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands