HP Cluster Platform Introduction Manual Download Page 56 | Manualshive

Page: 56 / 88

background image

is a single-phase unit that branches out into four single-phase branch circuits. The power strips
mount directly to the rear of the rack frame and plug into the control units.

Each HP Cluster Platform rack has up to four modular PDUs. For Cluster Platform racks with
server blades there may be up to eight modular PDUs in the rack. Each control unit has four
outlet receptacles. However, all four outlet receptacles might not be in use simultaneously because
the total capacity of each PDU cannot exceed 40A for PDU models shipped to the US and Japan
or exceed 32A for international PDU models. For the latest information on the power specifications,
see the HP Modular Power Distribution Units (Zero-U/1U Modular PDUs QuickSpecs, available
from:

http://h18000.www1.hp.com/products/quickspecs/11041_div/11041_div.html

Figure 2-31 Power Distribution Unit Zero-U Mount

1

3

2

4

6

5

7

8

The following list describes the callouts in

Figure 2-31

:

1.

Installation screws and cage nuts secure the PDU to the side of the rack column, adjacent to
the racks's side panel for servicing

2.

The rack's front left column

3.

Main inlet power cable, which is connected to the power supply

4.

Outlet power cables (up to 4) that connect to the power strips (see

Figure 2-33

)

5.

Connector shield, providing support for the outlet power cables

6.

PDU main breaker switch

7.

Individual breaker switches (four)

8.

Direction of view towards the rear of the rack

Note that the orientation and the hardware will be different for a 1U PDU installation. For more
information on how to install both the zero-PDU and 1U PDU control unit, see the HP Modular
Power Distribution Unit Kit Installation Instructions, available from:

http://bizsupport.austin.hp.com/

bc/docs/support/SupportManual/c00258165/c00258165.pdf

56

Platform Core Components

«
...
54
55
56
57
58
...
»

Summary of Contents for Cluster Platform

























































































Reviews:

No comments

Related manuals for Cluster Platform

ColorPASS-Z5000

Brand: Canon Pages: 130

BladeCenter HS23

Brand: IBM Pages: 36

Brand: Z Microsystems Pages: 17

APSolute Vision

Brand: Radware Pages: 81

UniServer R6900 G5

Brand: H3C Pages: 17

Brand: AIC Pages: 101

Brand: Atop Pages: 2

Brand: Sun Microsystems Pages: 12

PUZZLE-IN004 Series

Brand: IEI Technology Pages: 102

Brand: Dell Pages: 396

Brand: Dell Pages: 180

EqualLogic PS6010

Brand: Dell Pages: 57

PowerVault 700N

Brand: Dell Pages: 29

Brand: Dell Pages: 133

Brand: Kramer Pages: 2

Xtreme PC NG6050

Brand: Chip PC Pages: 4

Brand: Lantronix Pages: 100

Brand: B+B SmartWorx Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands