HP Cluster Platform Introduction Manual Download Page 63 | Manualshive

Page: 63 / 88

background image

3 Connecting and Powering Up the Core Cluster

Components

HP Cluster Platform cluster building blocks are connected, configured, and tested during the
manufacturing process. After technicians complete the final diagnostic process at the factory,
they disconnect the cables and package the cables separately from the cluster to prevent them
from being damaged during shipment. The cables are reconnected at the installation site.

This chapter provides an overview of the installation process for core components. It describes
how to connect the cluster's external network and power cables to the appropriate sources at the
customer site. It also describes the powering-up sequence.

The installation procedures assume that the cluster components (nodes, switches, and other
devices) are already installed in the racks and connected to a power strip within the rack when
they arrive at the customer site. The procedures also assume that the HP Cluster Platform software
is already installed on the cluster as described in the HP XC System Software Installation Guide.
These manuals are available from:

http://www.docs.hp.com/en/linuxhpc.html

For more information about these manuals and other related documentation, see

Preface

.

This chapter discusses the following topics:
•

Cabling the TFT7600 (

Section 3.1

)

•

Connecting the KVM to the control node (

Section 3.2

)

•

SVA Console Management Setup (

Section 3.3

)

•

Connecting the MSA1000, MSA1500, or MSA2000 controller to the control node (

Section 3.4

)

•

Powering-up sequence (

Section 3.5

)

The system interconnect cabling procedures are described in the documentation for the system
interconnects that are used in your model of HP Cluster Platform.

3.1 Cabling the TFT7600

The TFT7600 is connected to an eight-port console switch, or optionally connected directly to
the administrative (control) node, as shown in

Figure 3-1

.

3.1 Cabling the TFT7600

63

«
...
61
62
63
64
65
...
»

Summary of Contents for Cluster Platform

























































































Reviews:

No comments

Related manuals for Cluster Platform

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

Brand: B&B Electronics Pages: 67

Brand: Omega Pages: 16

Brand: TYAN Pages: 64

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

Brand: Santec Pages: 40

Intesis IBMBSDAL0640000

Brand: HMS Networks Pages: 39

Express5800/R320f-E4

Brand: NEC Pages: 88

Brand: IBM Pages: 1730

PRIMERGY CX400 M6

Brand: Fujitsu Pages: 209

PRIMERGY CX272 S1

Brand: Fujitsu Pages: 234

Primergy CX270 S2

Brand: Fujitsu Pages: 320

Primergy CX270 S2

Brand: Fujitsu Pages: 56

Brand: QNAP Pages: 39

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brand: Kramer Pages: 72

Brand: Dataton Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands