HP Cluster Platform Introduction Manual Download Page 71 | Manualshive

Page: 71 / 88

background image

4 Component Firmware

Your HP Cluster Platform configuration arrives with the latest versions of the firmware installed
on the components. However, the firmware for these components may be updated at a future
date. This manual does not provide instructions on how to install or upgrade firmware for the
components described in this document, but does provide pointers on where to obtain firmware
upgrades.

IMPORTANT:

Do not obtain firmware revisions from other HP or third-party Web sites. You must ensure that
the firmware revision is the same for all types of cluster component (nodes, switches, and
interconnects).

4.1 Component Firmware Updates

The following links provide you with pointers to firmware update sites for various interconnects
and other Cluster Platform components.

Caution:

Depending on how you subscribe for driver and firmware support, you might be advised of a
mandatory or recommended firmware upgrade for a specific cluster component. Even in the
case of mandatory upgrades, consult with your HP representative before proceeding with an
upgrade. Loading an unsupported firmware revision might prevent your cluster from functioning
correctly. If you are uncertain, verify the firmware revision through your normal support
escalation channel.

•

To obtain the latest firmware update information for the Cluster Platform components, go
to:

http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp

•

The HP InfiniBand Mezzanine HCA Cards and Mellanox InfiniBand PCI HCA Cards: Read This
First document provides information on where to download the latest firmware versions
for these HCAs and other product-related documentation. To access this document, go to:

http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c01570024/c01570024.pdf

•

The Cisco Supported Firmware Matrix provides information on the minimum firmware versions
required for correct operation of the Cisco InfiniBand interconnects with HP Cluster Platform
components. To access this document, go to:

http://www.docs.hp.com/en/14485/AC-CSFWM-1C.pdf

•

The Voltaire Supported Firmware Matrix provides information on the minimum firmware
versions required for correct operation of the Voltaire InfiniBand interconnects with HP
Cluster Platform components. To access this document, go to:

http://www.docs.hp.com/en/13620/AV-VSFWM-1C.pdf

•

The HP ProCurve Software for switches website provides software updates for the ProCurve
switches. To download firmware updates for your ProCurve switches, go to:

http://www.hp.com/rnd/software/switches.htm

•

The HP XC System Software Master Firmware Tables list the minimum firmware versions
required for correct operation of the latest version of HP XC System software. To access this
document, go to:

http://docs.hp.com/en/A-XCFM3-21B/A-XCFM3-21B.pdf

4.1 Component Firmware Updates

71

«
...
69
70
71
72
73
...
»

Summary of Contents for Cluster Platform

























































































Reviews:

No comments

Related manuals for Cluster Platform

Brand: IBM Pages: 438

8841 - eServer xSeries 236

Brand: IBM Pages: 100

Brand: Datacom Pages: 89

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

Brand: IBM Pages: 200

Brand: AIC Pages: 101

Thin Client 166

Brand: Tangent Pages: 2

Brand: Acer Pages: 20

Brand: Acer Pages: 20

AR360 F1 Series

Brand: Acer Pages: 20

Brand: Acer Pages: 18

AR380 F1 Series

Brand: Acer Pages: 17

Brand: Acer Pages: 134

Brand: Acer Pages: 23

AT350 F1 Series

Brand: Acer Pages: 23

Brand: Acer Pages: 160

Brand: Acer Pages: 95

AT350 F2 Series

Brand: Acer Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands