HP Cluster Platform Introduction Manual Download Page 60 | Manualshive

Page: 60 / 88

background image

Figure 2-36 PDU for SVA

U38

1

2

3

1.

Fasteners — quantity three (3).

2.

Attach the PDU to the rack chassis, and not the column inside the rack.

3.

PDU status monitoring screen.

Warning!

For installations in computer rooms with overhead power supplies, the maximum available
power cable length when routed to the top of the rack is approximately 36 inches. Never extend
the power cable emerging from the rack in any way. If you need to supply power from overhead
outlets, relocate the power supply outlets so that they are closer to the racks.

2.9 Storage

HP Cluster Platform clusters support the following optional external SAN storage:
•

MSA1000

•

MSA1500

•

MSA2000

•

EVA4000

•

EVA5000

•

SB40c Server Blade Storage

The MSA1000, MSA1500, and MSA2000 storage subsystems are mounted in the utility rack. The
EVA4000, and EVA5000 storage subsystems come mounted in their own 42U racks.

60

Platform Core Components

«
...
58
59
60
61
62
...
»

Summary of Contents for Cluster Platform

























































































Reviews:

No comments

Related manuals for Cluster Platform

BladeCenter HS20 Type 8843

Brand: IBM Pages: 112

System x3550 M3

Brand: IBM Pages: 160

System x3650 M4 Type 7915

Brand: IBM Pages: 192

Brand: IBM Pages: 694

System x3755 M3 7164

Brand: IBM Pages: 126

Brand: Xerox Pages: 2

DECT Server 2500

Brand: SpectraLink Pages: 27

PCS400R Pro:Centric

Brand: LG Pages: 57

Brand: LG Pages: 104

Pro:Centric PCS200S

Brand: LG Pages: 40

Brand: LG Pages: 6

PCS500R Pro:Centric

Brand: LG Pages: 70

Brand: LG Pages: 24

Centric PCS150R Pro

Brand: LG Pages: 35

Centric PCS200R Pro

Brand: LG Pages: 384

Brand: QNAP Pages: 55

SILVERSTREAM 3.75

Brand: RSA Security Pages: 11

Brand: Viavi Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands