manualshive.com logo in svg

HP Cluster Platform, Introduction Manual, Page: 12 / 88

Share
Download
HP Cluster Platform Introduction Manual Download Page 12

•

ProCurve (for cluster networking components, including Gigabit Ethernet interconnect).

•

Integrity (for cluster nodes).

•

”Rack 10000” (the HP 10000 Series Rack used in clusters).

•

techservers or HPC (The High-Performance Computing home page).

http://www.hp.com/products1/servers/integrity/index.html

– The US home page for Integrity

servers.

http://www.hp.com/rnd/index.htm

– The US home page for ProCurve networking.

http://h18004.www1.hp.com/products/servers/proliantstorage/racks/10000series/description.html

– The US home page for HP 10000 Series G1/G2 Racks, KVMs, console switches, and other rack
accessories.

http://h18004.www1.hp.com/products/servers/proliantstorage/racks/mcs/index.html

– The US

home page for HP Modular Cooling System.

http://www.hp.com/techservers/

– The US home page for High-Performance Technical Computing.

HP Encourages Your Comments

HP encourages your comments concerning this document. We are committed to providing
documentation that meets your needs. Send any errors found, suggestions for improvement, or
compliments to:

http://docs.hp.com/en/feedback.html

Include the document title, part number, and any comment, error found, or suggestion for
improvement you have concerning this document.

Text Annotations

The following annotations might appear in this guide:

Warning !

Text set off in this manner indicates that failure to follow directions could result in bodily harm
or loss of life

Caution:

Text set off in this manner indicates that failure to follow directions could result in equipment
damage or data loss.

Important:

Text set off in this manner presents clarifying information or specific instructions.

Note:

Text set off in this manner presents commentary, sidelights, or interesting points of information.

Conventions

This manual uses the following typographic conventions:

Monospace type

This type denotes literal items, such as command names, file names,
routines, directory names, path names, signals, messages, and
programming language structures.

12

Summary of Contents for Cluster Platform

























































































Reviews:

No comments