HP Cluster Platform Introduction Manual Download Page 40 | Manualshive

Page: 40 / 88

background image

No voltage range settings are required. The console port on the back of the ProCurve Series 2600
switches (see

Figure 2-11

) connect the switch to a console via a serial cable. The console can be

a PC or a workstation running a VT-100 terminal emulator.

Figure 2-11 HP ProCurve Series 2600 Switch, Rear View

Console

1

3

2

1.

Console port connector

2.

Cooling vents

3.

AC power inlet

The switch has two cooling vents, which must not be obstructed for proper switch operation.

Note:

The HP ProCurve switch is installed in the rack with the rear panel facing the front of the rack.

2.6.3 HP ProCurve 2848 and 2824 Ethernet Switch

The HP ProCurve Switch 2800 series consists of two switches: the 24-port HP ProCurve Switch
2824 with 20 10/100/1000 ports, and the 48-port HP ProCurve Switch 2848 with 44 10/100/1000
ports. In addition, each switch has 4 dual-personality ports for 10/100/1000 or mini-GBIC
connectivity.

The characteristics of the HP ProCurve 2800-series switches include:
•

48 Gb/sec backplane with up to 35.7 mpps (Switch 2824) and 96 Gbps backplane with up to
71.4 mpps (Switch 2848)

•

Dual-personality functionality: four 10/100/1000 ports or mini-GBIC slots for optional fiber
connectivity such as Gigabit-SX, -LX, or -LH

•

Basic IP routing: enables automatic routing with up to 16 external routes-including one
default route-in IP networks

•

IP multicast (data-driven IGMPv3): automatically prevents flooding of IP multicast traffic

•

802.3ad Link Aggregation Protocol (LACP) and HP trunking: support up to 24 trunks, each
with up to 8 links (ports) per trunk; trunking across modules is supported

•

Optional external redundant power supply: provides uninterrupted power; sold as an
accessory

•

RMON, XRMON, and SMON: provide advanced monitoring and reporting capabilities for
statistics, history, alarms, and events

•

Port security: prevents unauthorized access using MAC address lockdown

•

: eases switch management security administration by using a password
authentication server

•

Secure Shell (SSHv2): encrypts all transmitted data for secure remote access over IP networks

•

Secure Sockets Layer (SSL): encrypts all HTTP traffic, allowing secure access to the
browser-based management GUI in the switch

40

Platform Core Components

«
...
38
39
40
41
42
...
»

Summary of Contents for Cluster Platform

























































































Reviews:

No comments

Related manuals for Cluster Platform

Brand: Omneon Pages: 2

Brand: Premio Pages: 3

NovaScale T820 F2

Brand: Bull Pages: 34

Brand: Omega Pages: 49

Brand: Iwatsu Pages: 338

Brand: IBM Pages: 82

Brand: Cavalry Pages: 16

Brand: Rasilient Pages: 30

ZXCLOUD R5300 G3

Brand: Zte Pages: 19

Brand: ZyXEL Communications Pages: 115

Netra SPARC T3-1BA

Brand: Sun Oracle Pages: 62

Brand: Sun Oracle Pages: 182

Brand: Sun Oracle Pages: 222

Brand: Sun Microsystems Pages: 114

Brand: Sun Microsystems Pages: 192

Brand: Sun Microsystems Pages: 270

Advanced Office-in-a-Box

Brand: Enconnex Pages: 40

AirProjector KJ-200

Brand: TriLink Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands