HP BL30p - ProLiant - 1 GB RAM Troubleshooting Manual Download Page 104

Page: 104 / 152

Error messages 104

207-Invalid Memory Configuration - Incomplete Bank Detected in Bank X

Audible Beeps

: 1 long, 1 short

Possible Cause

: Bank is missing one or more DIMMs.

Action

: Fully populate the memory bank.

207-Invalid Memory Configuration - Insufficient Timings on DIMM

Audible Beeps

: 1 long, 1 short

Possible Cause

: The installed memory module is not supported.

Action

: Install a memory module of a supported type.

207-Invalid Memory Configuration - Mismatched DIMMs within DIMM Bank

Audible Beeps

: 1 long, 1 short

Possible Cause

: Installed DIMMs in the same bank are of different sizes.

Action

: Install correctly matched DIMMs.

207-Invalid Memory Configuration - Mismatched DIMMs within DIMM Bank...

...Memory in Bank X Not Utilized.

Audible Beeps

: 1 long, 1 short

Possible Cause

: Installed DIMMs in the same bank are of different sizes.

Action

: Install correctly matched DIMMs.

207-Invalid Memory Configuration - Mismatched DIMMs within DIMM Bank...

...Memory in Board X Bank X Not Utilized.

Audible Beeps

: 1 long, 1 short

Possible Cause

: Installed DIMMs in the same bank are of different sizes.

Action

: Install correctly matched DIMMs.

207-Invalid Memory Configuration - Unsupported DIMM in Bank x

Audible Beeps

: 1 long, 1 short

Possible Cause

: One of the DIMMs in bank X is of an unsupported type.

Action

: Install supported DIMMs to fill the bank.

207-Invalid Memory Configuration - Single channel memory...

...mode supports a single DIMM installed in DIMM socket 1. Please remove all other DIMMs or install memory in
valid pairs. System Halted.

Audible Beeps

: 1 long, 1 short

Possible Cause

: DIMMs are installed in pairs, but the server is in single channel memory mode.

Action

: Remove all other DIMMs or install memory in valid pairs and change the memory mode.

Summary of Contents for BL30p - ProLiant - 1 GB RAM

























































































































































Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands

HP BL30p - ProLiant - 1 GB RAM, Troubleshooting Manual

Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands