HP BL30p - ProLiant - 1 GB RAM Troubleshooting Manual Download Page 18

Page: 18 / 152

Common problem resolution 18

Online/activity LED
(green)

Fault/UID LED
(amber/blue)

Interpretation

Flashing irregularly Amber, flashing

regularly (1 Hz)

The drive is active, but a predictive failure alert has been
received for this drive. Replace the drive as soon as possible.

Flashing irregularly Off

The drive is active, and it is operating normally.

Off Steadily

amber

A critical fault condition has been identified for this drive, and
the controller has placed it offline. Replace the drive as soon as
possible.

Off

Amber, flashing
regularly (1 Hz)

A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.

Off Off The drive is offline, a spare, or not configured as part of an

array.

Summary of Contents for BL30p - ProLiant - 1 GB RAM

























































































































































Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands

HP BL30p - ProLiant - 1 GB RAM, Troubleshooting Manual

Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands