HP BL30p - ProLiant - 1 GB RAM Troubleshooting Manual Download Page 8

Page: 8 / 152

Contents 8

Swapped Cables or Configuration Error Detected. A Drive Rearrangement... ........................................ 88

Swapped Cables or Configuration Error Detected. An Unsupported Drive Arrangement Was Attempted... 88

Swapped cables or configuration error detected. The cables appear to be interchanged... ..................... 88

Swapped cables or configuration error detected. The configuration information on the attached drives... . 89

Swapped Cables or Configuration Error Detected. The Maximum Logical Volume Count X...................... 89

System Board is Unable to Identify which Slots the Controllers are in.................................................... 89

The Redundant Controllers Installed are not the Same Model............................................................... 89

This Controller Can See the Drives but the Other Controller Can't ........................................................ 90

This Controller Can't See the Drives but the Other Controller Can ........................................................ 90

Unable to Communicate with Drive on SCSI Port X, Drive ID Y ............................................................ 90

Unable to Retrieve Identify Controller Data. Controller May be Disabled or Failed ................................. 90

Unknown Disable Code.................................................................................................................. 90

Unrecoverable Read Error .............................................................................................................. 90

Unsupported Processor Configuration (Processor Required in Slot #1) .................................................. 91

Warning Bit Detected..................................................................................................................... 91

WARNING - Drive Write Cache is Enabled on X............................................................................... 91

WARNING - Mixed Feature Processors Were Detected ...................................................................... 91

WARNING - Resetting Corrupted CMOS ......................................................................................... 91

WARNING - Resetting Corrupted NVRAM........................................................................................ 91

WARNING - Resetting Corrupted System Environment........................................................................ 91

WARNING - Restoring Default Configurations as Requested ............................................................... 91

WARNING: Storage Enclosure on SCSI Bus X Indicated it is Operating in Single Ended Mode... ............ 92

Write Memory Error....................................................................................................................... 92

Wrong Accelerator........................................................................................................................ 92

POST error messages and beep codes ....................................................................................................... 92

Introduction to POST error messages ................................................................................................ 92

Non-numeric messages or beeps only .............................................................................................. 93

100 Series ................................................................................................................................. 101

200 Series ................................................................................................................................. 103

300 Series ................................................................................................................................. 106

400 Series ................................................................................................................................. 107

600 Series ................................................................................................................................. 108

1100 Series ............................................................................................................................... 109

1600 Series ............................................................................................................................... 109

1700 Series ............................................................................................................................... 112

Event list error messages ........................................................................................................................ 124

Introduction to event list error messages.......................................................................................... 124

A CPU Power Module (System Board, Socket X)... ........................................................................... 124

ASR Lockup Detected: Cause ........................................................................................................ 124

Automatic operating system shutdown initiated due to fan failure....................................................... 125

Automatic Operating System Shutdown Initiated Due to Overheat Condition... .................................... 125

Blue Screen Trap: Cause [NT]... .................................................................................................... 125

Corrected Memory Error Threshold Passed (Slot X, Memory Module Y)............................................... 125

EISA Expansion Bus Master Timeout (Slot X)... ................................................................................. 125

PCI Bus Error (Slot X, Bus Y, Device Z, Function X) ........................................................................... 125

Processor Correctable Error Threshold Passed (Slot X, Socket Y)......................................................... 125

Processor Uncorrectable Internal Error (Slot X, Socket Y) ................................................................... 125

Real-Time Clock Battery Failing...................................................................................................... 126

System AC Power Overload (Power Supply X)................................................................................. 126

System AC Power Problem (Power Supply X)................................................................................... 126

System Fan Failure (Fan X, Location) .............................................................................................. 126

System Fans Not Redundant.......................................................................................................... 126

System Overheating (Zone X, Location) .......................................................................................... 126

System Power Supplies Not Redundant........................................................................................... 126

Summary of Contents for BL30p - ProLiant - 1 GB RAM

























































































































































Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands

HP BL30p - ProLiant - 1 GB RAM, Troubleshooting Manual

Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands