HP BL30p - ProLiant - 1 GB RAM Troubleshooting Manual Download Page 112

Page: 112 / 152

Error messages 112

1615-Power Supply Configuration Error

Audible Beeps

: None

Possible Cause

: The server configuration requires an additional power supply. A moving bar is

displayed, indicating that the system is waiting for another power supply to be installed.

Action

: Install the additional power supply.

1615-Power Supply Configuration Error

- A working power supply must be installed in Bay 1 for proper cooling.
- System Halted!

Audible Beeps

: None

Possible Cause

: The server configuration requires an additional power supply. A moving bar is

displayed, indicating that the system is waiting for another power supply to be installed.

Action

: Install the additional power supply.

1615-Power Supply Failure, Power Supply Unplugged, or Power Supply Fan Failure in Bay X

Audible Beeps

: None

Possible Cause

: The power supply has failed, or it is installed but not connected to the system board or

AC power source.

Action

: Reseat the power supply firmly and check the power cable or replace power supply.

1616-Power Supply Configuration Failure

-A working power supply must be installed in Bay 1 for proper cooling.
-System Halted!

Audible Beeps

: None

Possible Cause

: Power supply is improperly configured.

Action

: Run the server setup utility and correct the configuration.

1700 Series

1711-Slot Z Drive Array - RAID ADG Logical Drive(s) Configured but Array Accelerator Size <=
32 MB...

...This configuration is not recommended. Consider migrating logical drive(s) to RAID 5 or upgrading the Array
Accelerator module.

Audible Beeps

: None

Possible Cause

: This configuration is not recommended.

Action

: Migrate logical drives to RAID 5 or upgrade to a larger array accelerator module.

1712-Slot X Drive Array - RAID 5 logical drive(s) configured with 56 Drives, but Array
Accelerator size <= 32 MB...

...This configuration is not recommended. Consider migrating logical drive(s) to RAID 0 or 1, reducing the number
of drives in the array, or upgrading the Array Accelerator module.

Summary of Contents for BL30p - ProLiant - 1 GB RAM

























































































































































Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands

HP BL30p - ProLiant - 1 GB RAM, Troubleshooting Manual

Search results

Summary of Contents for BL30p - ProLiant - 1 GB RAM

Reviews:

Related manuals for BL30p - ProLiant - 1 GB RAM

Brands by name

Popular brands