HP BL30p - ProLiant - 1 GB RAM Troubleshooting Manual Download Page 118 | Manualshive

Page: 118 / 152

background image

Error messages 118

1776-Drive Array Reports Improper SCSI Port 1 Cabling

Audible Beeps

: None

Possible Cause

:

•

The integrated array enabler board failed.

•

The I/O board, drive backplane fan board, or drive backplane failed.

Action

:

1.

Replace the integrated array enabler board.

2.

Update the integrated Smart Array option to the latest firmware version ("

Firmware maintenance

" on

page

65

).

CAUTION:

Only authorized technicians trained by HP should attempt to remove the I/O board. If you

believe the I/O board requires replacement, contact HP Technical Support before proceeding.

3.

Reboot the server after replacing each item:

a.

Drive backplane fan board

b.

Drive backplane

c.

I/O board

1777-Slot X Drive Array - ProLiant Drive Storage Enclosure Problem Detected...

(followed by one or more of the following):
...SCSI Port Y: Cooling Fan Malfunction Detected
SCSI Port Y: Overheated Condition Detected
SCSI Port Y: Side-Panel must be Closed to Prevent Overheating
SCSI Port Y: Redundant Power Supply Malfunction Detected
SCSI Port Y: Wide SCSI Transfer Failed
SCSI Port Y: Interrupt Signal Inoperative
SCSI Port y: Unsupported ProLiant Storage System Detected

Audible Beeps

: None

Possible Cause

: Environment threshold was violated on the drive enclosure.

Action

:

•

Check cooling fan operation by placing a hand over the fan.

•

Be sure the internal plenum cooling fan in tower servers or storage systems is operational. If the fan
is not operating, check for obstructions and check all internal connections.

•

Replace unit side panel if removed.

•

Check the LEDs. If the ProLiant Storage System power LED is amber instead of green, this indicates a
redundant power supply failure.

•

If the message indicates to check SCSI cables:

a.

Compare the cabling against the diagrams in the

HP Smart Array Controller User Guide

.

b.

If the routing is correct, replace cables on the specified port until the POST error message is
eliminated.

1778-Drive Array Resuming Automatic Data Recovery Process

Audible Beeps

: None

Possible Cause

: A controller reset or power cycle occurred while Automatic Data Recovery was in

progress.

Action

: No action is required.

«
...
116
117
118
119
120
...
»

Summary of Contents for BL30p - ProLiant - 1 GB RAM

























































































































































Reviews:

No comments

Related manuals for BL30p - ProLiant - 1 GB RAM

Power System 8247-21L

Brand: IBM Pages: 60

Brand: Aztech Pages: 2

Brand: StarTech.com Pages: 18

Versa WiFi USB Adapter 3

Brand: C. Crane Pages: 30

Brand: Renkforce Pages: 7

Brand: Shimano Pages: 39

PV-KBT4 UR Series

Brand: Staubli Pages: 12

Brand: Digitus Pages: 7

Brand: Daikin Pages: 20

SNG 12/1500-OW-N

Brand: VOLTCRAFT Pages: 4

Brand: Axial Pages: 6

Brand: U.S. Converters Pages: 8

Brand: VARIZOOM Pages: 2

Brand: Flying Voice Pages: 46

Brand: Westermo Pages: 28

Brand: Sharp Pages: 2

Brand: Sharp Pages: 13

Brand: Sharp Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands