HP 4500G PWR 24-Port Configuration Manual Download Page 41 | Manualshive

Page: 41 / 1968

background image

1-3

Figure 1-1

An application diagram of auto-negotiation transmission rate

As shown in

Figure 1-1,

the network card transmission rate of the server group (Server 1, Server 2, and

Server 3) is 1000 Mbps, and the transmission rate of GigabitEthernet 1/0/4, which provides access to
the external network for the server group, is 1000 Mbps too. If you do not specify an auto-negotiation
range, the transmission rate on GigabitEthernet 1/0/1, GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3
through negotiation with the servers is 1000 Mbps, which may cause congestion on the egress port
GigabitEthernet 1/0/4. To solve the problem, you can specify the auto-negotiation transmission rate on
GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 to 100 Mbps.
Follow these steps to configure an auto-negotiation transmission rate:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enter Ethernet port view

interface interface-type
interface-number

—

Configure the auto-negotiation

transmission rate range

speed

auto

[

10

|

100

|

1000

] * Optional

z

This function is available for auto-negotiation-capable Gigabit Layer-2 Ethernet electrical ports
only.

z

If you repeatedly use the

speed

and the

speed auto

commands to configure the transmission rate

on a port, only the latest configuration takes effect.

Configuring Flow Control on an Ethernet Interface

When flow control is enabled on both sides, if traffic congestion occurs at the ingress interface, it will
send a Pause frame notifying the egress interface to temporarily suspend the sending of packets. The
egress interface is expected to stop sending any new packet when it receives the Pause frame. In this
way, flow control helps to avoid dropping of packets. Note that this will be possible only after flow control
is enabled on both the ingress and egress interfaces.

«
...
39
40
41
42
43
...
»

Summary of Contents for 4500G PWR 24-Port

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 4500G PWR 24-Port

Brand: ABB Pages: 32

Brand: ABB Pages: 44

Brand: ABB Pages: 15

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

DKVM-16 - KVM Switch

Brand: D-Link Pages: 24

Dis-200G Series

Brand: D-Link Pages: 161

Dis-200G Series

Brand: D-Link Pages: 16

Dis-200G Series

Brand: D-Link Pages: 47

Brand: D-Link Pages: 25

DGS-3100 SERIES

Brand: D-Link Pages: 54

DGS-3100 SERIES

Brand: D-Link Pages: 220

Brand: D-Link Pages: 24

DGS-1248T - Switch

Brand: D-Link Pages: 52

DGS-1216T - Switch

Brand: D-Link Pages: 42

DGS-1216T - Switch

Brand: D-Link Pages: 10

Brand: D-Link Pages: 8

Brand: D-Link Pages: 379

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands