Honeywell Rapid Eye Hybrid LT Installation Manual Download Page 73

Page: 73 / 86

Document 800-07766V4 Rev A

01/2013

Horizontal and Vertical Unit Installations

Rubber Feet and the Orientation of Unit Installations

The Rapid Eye Hybrid LT unit can be installed one of the two following orientations (see

Figure C-1

•

Horizontal. The rubber feet come pre-installed on the unit for horizontal installations.

•

Vertical. If a vertical installation is required, see

Installing Rubber Feet for a Vertical

Installation

on page

for the procedure to change the rubber feet placements on

your Rapid Eye Hybrid LT DVR.

Figure C-1

Rubber Feet Placement for Vertical and Horizontal Installations

Keep the rubber feet installed on the bottom of the unit
if you are using a horizontal installation.

Remove the rubber feet from the unit bottom and screw
the rubber feet into the left side of the unit if you are
using a vertical installation.

Rapid Eye Hybrid LT unit
installed horizontally

Rapid Eye Hybrid
LT unit installed
vertically

Summary of Contents for Rapid Eye Hybrid LT























































































Search results

Summary of Contents for Rapid Eye Hybrid LT

Reviews:

Related manuals for Rapid Eye Hybrid LT

Brands by name

Popular brands

Honeywell Rapid Eye Hybrid LT, Installation Manual

Search results

Summary of Contents for Rapid Eye Hybrid LT

Reviews:

Related manuals for Rapid Eye Hybrid LT

Brands by name

Popular brands