Honeywell AlarmNet IGSMV, Installation And Setup Manual, Page: 39 / 64

Section 3: Programming the IGSMV
3-19
PROMPTS
ZONE
TRIG.
4204/
2-4204
ENTRY OPTIONS DESCRIPTION
50
Rpt Zn4 ONLY if
Armed (N)_
 2-
4204
only
[Y], [N]
Reports alarms on zone 4 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 8 in 2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 4.
51
Zn5 Trigger Type
(V+)_

 (V+)

(V–)
 (EOLR)
Selects the triggering method for this zone
input.
Press the [space] key to scroll through
choices.
UL: V+ must be set as inverted and V– as
non-inverted.
52
Invert Zn5 Y/N
(N)_

[Y], [N] Inverts the alarm and normal states of the
zone 5 trigger; otherwise uses normal input
signal.
53 Restore Zn5 Y/N
(Y)_

2-
4204
only
[Y], [N] Enables restore reporting for zone 5.
UL/ULC: Must be set to “Y.”
54
Delay Zn5 (secs)
(00)_
 2-
4204
only
[01-15]
[00] = no delay Defines the reporting delay in seconds for
zone 5.
UL/ULC: Must be set to “00.”
55
Rpt Zn5 ONLY if
Armed (N)_
 2-
4204
only
[Y], [N]
Reports alarms on zone 5 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 8 in 2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 5.
56
Enable Zn6 Y/N
(N)_
4204
only
[Y], [N]
Enables alarm reporting for zone 6.
If [N], skip to Prompt 62: "Enable Zn7."
57 Zn6 Trigger Type
(V+)_
 4204
only
 (V+)
 (V–)
 (EOLR)
Selects the triggering method for this zone
input.
Press the [space] key to scroll through
choices.
UL: V+ must be set as inverted and V– as
non-inverted.
58 Invert Zn6 Y/N
(N)_
 4204
only
[Y], [N] Inverts the alarm and normal states of the
zone 6 trigger; otherwise uses normal input
signal.
59
Restore Zn6 Y/N
(Y)_
 
[Y], [N] Enables restore reporting for zone 6.
UL/ULC: Must be set to “Y.”
60
Delay Zn6 (secs)
(00)_
 
[01-15]
[00] = no delay Defines the reporting delay in seconds for
zone 6.
UL/ULC: Must be set to “00.”
61 Rpt Zn6 ONLY if
Armed (N)_
 
[Y], [N]
Reports alarms on zone 6 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 4 in 4204 mode; zone 8 in 2-4204 mode)
is triggered (armed).
If [N], always reports alarms on zone 6.
62
Enable Zn7 Y/N
(N)_
4204
only
[Y], [N] Enables alarm reporting for zone 7.
If [N], skip to Prompt 70: "Use DHCP."
63
Zn7 Trigger Type
(V+)_
 4204
only
 (V+)

(V–)
 (EOLR)
Selects the triggering method for this zone
input.
Press the [space] key to scroll through
choices.
UL: V+ must be set as inverted and V– as
non-inverted.