manualshive.com logo in svg

Hitachi H8/3660, Hardware Manual

The Hardware Manual for the powerful Hitachi H8/3660 microprocessor is now available for free download! This comprehensive manual provides in-depth information and guidance on utilizing the H8/3660's advanced features. Access this valuable resource at manualshive.com and unlock the full potential of your Hitachi H8/3660 device.

Share
Download
background image

175

11.2.4

Timer Control/Status Register V (TCSRV)

 Bit

 7

 6

 5

 4

 3

 2

 1

 0

 

 CMFB

 CMFA

 OVF

 —

 OS3

 OS2

 OS1

 OS0

 Initial value

 0

 0

 0

 1

 0

 0

 0

 0

 Read/Write

 R/(W)

*

 R/(W)

*

 R/(W)

*

 —

 R/W

 R/W

 R/W

 R/W

Note: 

*

Bits 7 to 5 can be only written with 0, for flag clearing.

 

 TCSRV is an 8-bit register that sets compare match flags and the timer overflow flag, and controls
compare match output.

 TCSRV is initialized to H'10 upon reset and in standby mode, subsleep mode, and subactive
mode.

 Bit 7—Compare Match Flag B (CMFB): Bit 7 is a status flag indicating that TCNTV has
matched TCORB. This flag is set by hardware and cleared by software. It cannot be set by
software.

 Bit 7:  CMFB

 Description

 0

 Clearing conditions:
After reading CMFB = 1, cleared by writing 0 to CMFB

(Initial value)

 1

 Setting conditions:
Set when the TCNTV value matches the TCORB value

 

 Bit 6—Compare Match Flag A (CMFA): Bit 6 is a status flag indicating that TCNTV has
matched TCORA. This flag is set by hardware and cleared by software. It cannot be set by
software.

 Bit 6:  CMFA

 Description

 0

 Clearing conditions:
After reading CMFA = 1, cleared by writing 0 to CMFA

(Initial value)

 1

 Setting conditions:
Set when the TCNTV value matches the TCORA value

 

Summary of Contents for H8/3660
















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3660

IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
H3C NIC-FC730i-Mb-2-32G Manual preview
NIC-FC730i-Mb-2-32G
Brand: H3C Pages: 37
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Brand: Supermicro Pages: 54
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
Disc Makers Reflex10 User Manual preview
Reflex10
Brand: Disc Makers Pages: 38
Alarm NX-208E Installation Manual preview
NX-208E
Brand: Alarm Pages: 5
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Brand: Primera Pages: 2
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Brand: Z-Wave Pages: 42
EK-Quantum 3831109836897 User Manual preview
3831109836897
Brand: EK-Quantum Pages: 14
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Brand: Adaptec Pages: 2
Crystal Vision Indigo 4 CoolFlow User Manual preview
Indigo 4 CoolFlow
Brand: Crystal Vision Pages: 49
Cambium Networks PTP 300 Series Installation Manual preview
PTP 300 Series
Brand: Cambium Networks Pages: 32
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Brand: Extron electronics Pages: 10
AMX TP4-VID Specifications preview
TP4-VID
Brand: AMX Pages: 1
mikroElektronika Keypad 4x4 Manual preview
Keypad 4x4
Brand: mikroElektronika Pages: 6
Lava ISA Bus Bi-Directional Parallel Port Board Datasheet preview
ISA Bus Bi-Directional Parallel Port Board
Brand: Lava Pages: 1
Secure Computing sidewinder Startup Manual preview
sidewinder
Brand: Secure Computing Pages: 68
STONEFLY DR365V-3605 Setup Manual preview
DR365V-3605
Brand: STONEFLY Pages: 48

Brands by name

Popular brands

Load more brands