manualshive.com logo in svg

Hitachi H8/3660, Hardware Manual

The Hardware Manual for the powerful Hitachi H8/3660 microprocessor is now available for free download! This comprehensive manual provides in-depth information and guidance on utilizing the H8/3660's advanced features. Access this valuable resource at manualshive.com and unlock the full potential of your Hitachi H8/3660 device.

Share
Download
background image

255

Bit 3—Multiprocessor Interrupt Enable (MPIE): Bit 3 selects enabling or disabling of the
multiprocessor interrupt request. The MPIE bit setting is only valid when asynchronous mode is
selected and reception is carried out with bit MP in SMR set to 1. The MPIE bit setting is invalid
when bit COM is set to 1 or bit MP is cleared to 0.

Bit 3:  MPIE

Description

0

Multiprocessor interrupt request disabled (normal receive operation)

(Initial value)

[Clearing condition]

When data is received in which the multiprocessor bit is set to 1

1

Multiprocessor interrupt request enabled

*

Note: 

*

Receive data transfer from RSR to RDR, receive error detection, and setting of the RDRF,
FER, and OER status flags in SSR is not performed. RXI, ERI, and setting of the RDRF,
FER, and OER flags in SSR, are disabled until data with the multiprocessor bit set to 1 is
received. When a receive character with the multiprocessor bit set to 1 is received, bit
MPBR in SSR is set to 1, bit MPIE is automatically cleared to 0, and RXI and ERI requests
(when bits TIE and RIE in serial control register (SCR) are set to 1) and setting of the
RDRF, FER, and OER flags are enabled.

Bit 2—Transmit End Interrupt Enable (TEIE): Bit 2 selects enabling or disabling of the
transmit end interrupt request (TEI) if there is no valid transmit data in TDR when MSB data is to
be sent.

Bit 2:  TEIE

Description

0

Transmit end interrupt request (TEI) disabled

(Initial value)

1

Transmit end interrupt request (TEI) enabled

*

Note: 

*

TEI can be released by clearing bit TDRE to 0 and clearing bit TEND to 0 in SSR, or by
clearing bit TEIE to 0.

Bits 1 and 0—Clock Enable 1 and 0 (CKE1, CKE0): Bits 1 and 0 select the clock source and
enabling or disabling of clock output from the SCK

3

 pin. These bits determine whether the SCK

3

pin functions as an I/O port, a clock output pin, or a clock input pin.

The CKE0 bit setting is only valid in case of internal clock operation (CKE1 = 0) in asynchronous
mode. In synchronous mode, or when external clock operation is used (CKE1 = 1), bit CKE0
should be cleared to 0.

After setting bits CKE1 and CKE0, set the operating mode in the serial mode register (SMR).

For details on clock source selection, see table 14.7 in 14.2.8, Operation.

Summary of Contents for H8/3660
















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3660

D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Brand: D-Link Pages: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Brand: D-Link Pages: 78
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
Dahua NVRPRO User Manual preview
NVRPRO
Brand: Dahua Pages: 113
Xenteq SR 200-12 User Manual preview
SR 200-12
Brand: Xenteq Pages: 16
Maxtor DiamondMax 8S Specification Sheet preview
DiamondMax 8S
Brand: Maxtor Pages: 2
ekwb 3831109826140 User Manual preview
3831109826140
Brand: ekwb Pages: 11
Adaptec Serial Attached SCSI (SAS) Expander Card Installation And User Manual preview
Serial Attached SCSI (SAS) Expander Card
Brand: Adaptec Pages: 26
Quadram Quadboard Operation Manual preview
Quadboard
Brand: Quadram Pages: 21

Brands by name

Popular brands

Load more brands