Hill-Rom DuraStar Series Service Manual Download Page 72

Page: 72 / 165

4.5 Base Shroud Cover

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 15

Replacement

NOTE:
The shroud is held in place with Velcro®

strips.

1. Install the shroud (A), bellows (B), and the bellows attachment (C).

2. Ensure the shroud cover seats firmly into position and makes contact with

all Velcro® strips.

3. For the DuraStar™

Hydraulic Stretcher, install the upper frame assembly

(refer to procedure 4.4). For the DuraStar™ Fixed Height Stretcher, install
the upper frame assembly (refer to procedure 4.8).

4. Check the shroud and bellows for proper operation.

5. To ensure proper operation of the DuraStar™ Hydraulic Stretcher, perform

the “DuraStar™ Hydraulic Stretcher Function Checks” on page 2-4. To
ensure proper operation of the DuraStar™ Fixed Height Stretcher, perform
the “DuraStar™ Fixed Height Stretcher Function Checks” on page 2-7.

Summary of Contents for DuraStar Series






































































































































































Search results

Summary of Contents for DuraStar Series

Reviews:

Brands by name

Popular brands

Hill-Rom DuraStar Series, Service Manual

Search results

Summary of Contents for DuraStar Series

Reviews:

Brands by name

Popular brands