manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 70

4.4  DuraStar™ Hydraulic Stretcher Upper Frame

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 13

4

WARNING:

Two people are required for this procedure. If you do not use two 
people, personal injury could occur.

CAUTION:

Be careful not to damage the base shroud when you remove the upper 
frame assembly.

3. As you lift the upper frame assembly, tap on the underside of the round 

crosstube (C) with a rubber mallet/hammer until the frame separates from 
the hydraulic cylinder shaft.

4. Lift the frame from the hydraulic cylinders.

Replacement

WARNING:

Two people are required for this procedure. If you do not use two 
people, personal injury could occur.

CAUTION:

Be careful not to damage the base shroud when you install the upper 
frame assembly.

1. Lift the upper frame, and put the round crosstube (C) of the upper frame 

onto the hydraulic cylinders. 

2. Ensure the frame is in position on both cylinders.

3. Using the ratchet and the 9/16" socket, install the washer (D), lockwasher 

(B), and bolt (A) to secure the upper frame to the hydraulic cylinder. 

4. Using the torque wrench, torque the bolt (A) to 125 + 19 in-lb (14.1 + 2.1 

N·m).

5. To ensure proper operation, verify that the frame is in position and secured 

on both cylinders.

6. To ensure proper operation of the DuraStar™ Hydraulic Stretcher, perform 

the “DuraStar™ Hydraulic Stretcher Function Checks” on page 2-4.

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands