manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 66

4.3  Stretcher Back Panel Gas Spring

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 9

4

CAUTION:

Do not overextend the retaining rings. If the retaining rings are 
overextended, use new ones for the installation. Equipment damage 
can occur.

3. Using the retaining ring removal/installation tool, remove the retaining 

rings (A) and (F) from the top and bottom headed pins (B) and (E). Do not 
remove the headed pins at this time.

4. Lower the back panel to the horizontal position, and remove the bottom 

headed pin (E) from the gas spring (G).

5. Raise the back panel, and remove the top headed pin (B) from the gas 

spring (G). 

6. Remove and discard the gas spring (G).

Replacement

WARNING:

Ensure you fully control the lift of the back section. The back section 
could rise quickly with little or no weight on it, and personal injury could 
occur.

1. Raise the back panel, put the new gas spring (G) into position, and install 

the top headed pin (B).

2. Lower the back panel to the horizontal position, and install the bottom 

headed pin (E) through the gas spring (G) and frame bracket.

WARNING:

Do not use retaining rings that are overextended. Personal injury could 
occur.

3. Ensure the retaining rings are not overextended.

4. Using the retaining ring removal/installation tool, install the retaining rings 

(A) and (F) into the grooves of the top and bottom headed pins (B) and (E). 

5. Install the solid rivet (C) that secures the release handle to the gas spring 

(G).

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands