Hill-Rom DuraStar Series Service Manual Download Page 65

Page: 65 / 165

4.3 Stretcher Back Panel Gas Spring

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 8

DuraStar™ Series Stretcher Service Manual (man268)

4.3

Stretcher Back Panel Gas Spring

Tools required:

Screwdriver

Pliers

Retaining ring removal/installation tool
17 mm wrench

Removal

WARNING:

Ensure you fully control the lift of the back section. The back section
could rise quickly with little or no weight on it, and personal injury could
occur.

1. Raise the back panel to the 90° position.

2. Using the pliers and the screwdriver, remove the push nut (D) from the

solid rivet (C) that secures the release handle to the gas spring (G) (see
figure 4-3 on page 4-8).

Figure 4-3. Back Panel Gas Spring Replacement

m268_058

Summary of Contents for DuraStar Series






































































































































































Search results

Summary of Contents for DuraStar Series

Reviews:

Brands by name

Popular brands

Hill-Rom DuraStar Series, Service Manual

Search results

Summary of Contents for DuraStar Series

Reviews:

Brands by name

Popular brands