manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 62

4.2  Stretcher Siderail Latch

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 5

4

4.2

Stretcher Siderail Latch

Tools required:

T30 Torx®

1

 head bit

Ratchet

Torque wrench 0-250 in-lb

1/4" socket

Parts required:

(1)

46362

Lower pivot bolt 

(1)

6515201

Siderail latch

(1)

48645

Shoulder bolt latch

Removal

1. Remove the bottom rail end caps (A) from the bent bottom rail extension 

(B).

2. Remove the side rail trim strip (C) from the bent bottom rail extension (B).

3. Using the ratchet and the T30 Torx® head bit, remove and discard the latch 

shoulder bolt (D) that secures the latch (E) to the end tube (F) (see figure 4-
2 on page 4-5).

Figure 4-2.  Latch Replacement

1. Torx® is a registered trademark of Textron, Inc.

m268_033

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands