manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 26

General Operation

Chapter 1: Introduction

DuraStar™ Series Stretcher Service Manual (man268)

Page 1 - 17

1

Trendelenburg/Reverse Trendelenburg Operation

The Trendelenburg/Reverse Trendelenburg pedals are located on both sides of 
the hydraulic stretcher. The stretcher must be in a raised position to achieve 
Trendelenburg/Reverse Trendelenburg positions.

Trendelenburg

Press the foot pedal marked with the graphic showing Trendelenburg until the 
desired angle is reached.

Reverse Trendelenburg

Press the foot pedal marked with the graphic showing Reverse Trendelenburg 
until the desired angle is reached.

Quick Trendelenburg

Grasp the permanent push handle located at the foot end, and pull up on the 
stretcher until the desired angle is reached.

Leveling the Sleep Surface 

• If the stretcher is in the Trendelenburg position, press the Reverse 

Trendelenburg pedal until the stretcher is level.

• If the stretcher is in the Reverse Trendelenburg position, press the 

Trendelenburg pedal until the stretcher is level.

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands