manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 157

7.4  IV Transporter

Chapter 7: Accessories

Page 7 - 10

DuraStar™ Series Stretcher Service Manual (man268)

8. Using the ratchet and the 3/4" socket, install one Oilite®

1

 bushing (G), D-

washer (H), one belleville washer (I) (concave up), one belleville washer 
(J) (concave down), one belleville washer (K) (concave up), and castle nut 
(L) to secure the tow bar post weldment (E) to the base frame.

9. Using the torque wrench, torque the castle nut (L) to 200 in-lb (22.6 N·m).

10. Swing the tow arm (A) through a full range of motion. 

11. If the tow arm makes a squeaking noise, loosen the castle nut (L) until the 

squeaking stops.

12. Install a portable IV pole into the transporter. Make sure the transporter 

arm stays in position when the stretcher is moved.

13. See if the slot in the castle nut (L) aligns with the hole in the tow bar post 

weldment (E). 

14. If the hole and slot do not line up, tighten or loosen the castle nut (L) just 

enough to align the slots.

15. Insert the cotter pin (M) through the castle nut (L) and the tow bar post 

weldment (E).

16. Bend the cotter pin (M) around the castle nut (L).

17. Put the tow arm assembly (A) over the tow bar post weldment (E), and 

insert the headed pin (B) through the tow arm assembly (A) and tow bar 
post weldment (E).

18. Install the retaining ring (C) to secure the headed pin (B).

1. 

Oilite® is a registered trademark of Beemer Precision, Incorporated.

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands