manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 24

Model Identification

Chapter 1: Introduction

DuraStar™ Series Stretcher Service Manual (man268)

Page 1 - 15

1

Model Identification

See table 1-2 on page 1-15 for DuraStar™ Series Stretcher model 
identification.

Table 1-2.  Model Identification

General Operation

The DuraStar™ Series Stretcher is a mechanically operated stretcher. The 
following paragraphs explain the basic operation of this stretcher.

Siderail Operation

Raising the Siderail

• Pull the siderail up until it locks into position.

• To ensure it is fully locked, push the siderail down.

Lowering the Siderail

• Lift on the siderail release handle, and push down on the siderail.

• Lower the siderail completely.

Model Number

Description

P8005

DuraStar™ Hydraulic Stretcher

P8035

DuraStar™ Fixed Height Stretcher

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands