manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 155

7.4  IV Transporter

Chapter 7: Accessories

Page 7 - 8

DuraStar™ Series Stretcher Service Manual (man268)

7.4

IV Transporter

Tools required:

Drill

Ratchet

1/4" drill bit

Torque wrench

7/8" drill bit

3/4" socket

Retaining ring removal/installation tool

The IV transporter attaches to the base of the stretcher and enables the 
transport of a portable IV pole without the assistance of the caregiver.

The IV transporter can be mounted on either the right or left side of the 
stretcher at the head end only.

Installation

1. Decide on which side of the stretcher you will mount the transporter.

NOTE:
The proper location for the transporter hole is indicated by dimples located on 
the inside surface on both sides of the head end of the shroud. 

2. Lift the shroud, and locate the dimple at the head end of the shroud that 

corresponds to the location where you want to mount the IV transporter. 

3. Using the drill and the 1/4" drill bit, drill a 1/4" (6.4 mm) pilot hole through 

the center of the dimple.

4. Using the drill with the 7/8" drill bit and the pilot hole as a guide, carefully 

drill a 7/8" (22.4 mm) hole through the shroud.

5. Install the rubber grommet (D) into the hole you just drilled in the shroud 

(see figure 7-4 on page 7-9).

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands