manualshive.com logo in svg

Hill-Rom DuraStar Series, Service Manual

Share
Download
Hill-Rom DuraStar Series Service Manual Download Page 42

2.1  Reduced Braking Ability

Chapter 2: Troubleshooting Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 2 - 9

2

2.1

Reduced Braking Ability

1. The brake/steer pedal locks into the brake position.

Yes

No

↓

→

Check the brake/steer link at the head and foot ends of the 
stretcher for proper orientation. If this solves the problem, go to 
“Final Actions” on page 2-8. Otherwise, continue to step 2.

2. When the brake/steer pedal is activated, the hex rod rotates 45° in either 

direction from neutral.

Yes

No

↓

→

Check the brake/steer link at the head and foot ends of the 
stretcher for proper orientation. If this solves the problem, go to 
“Final Actions” on page 2-8. Otherwise, continue to step 3.

3. All four caster brake shoes are properly adjusted. 

Yes

No

↓

→

Adjust the brake caster shoes (refer to procedure 4.9). If this 
solves the problem, go to “Final Actions” on page 2-8. 
Otherwise, go to step 4.

4. All four casters lock in the brake position and do not rotate or swivel.

Yes

No

↓

→

Replace the damaged caster(s) (refer to procedure 4.6). If this 
solves the problem, go to “Final Actions” on page 2-8. 
Otherwise, go to step 5.

5. Another part of the stretcher interferes with the brake/steer mechanism.

Yes

No

↓

→

Call Hill-Rom Technical Support at (800) 445-3720.

6. Take appropriate actions to eliminate the interference. This solves the 

problem.

Yes

No

↓

→

Call Hill-Rom Technical Support at (800) 445-3720.

7. Go to “Final Actions” on page 2-8.

Summary of Contents for DuraStar Series






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands