Herz pelletfire 20/20 Operating Instructions Manual Download

Page: 69 / 100

Menu navigation and adjustment values

9.14.9

Service special

Navigation:

Screen:

By pressing the button:

Status module

the status of the external modules is displayed

Format USB-

Stick

the USB stick can be formatted.

Backup

a backup can be created. The backup can be stored directly in the control and/or on an
USB-stick.

9.14.10

Cascade

Navigation:

Screen:

By pressing the button:

Cascade
overview

Cascade overview shows every cascade user and its actual status and operating hours
within the cascade.

the „cascade status“ menu will be displayed.

the menu for the "cascade settings" will be displayed.

the „cascade network“ menu will be displayed.

Summary of Contents for pelletfire 20/20





































































































Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands

Herz pelletfire 20/20, Operating Instructions Manual

Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands