Herz pelletfire 20/20 Operating Instructions Manual Download

Page: 30 / 100

Menu navigation and adjustment values

9.9

Main menu values

9.9.1

Adding / defining display values

Navigation 1:

Code

– entry (chapter 9.5)

Navigation 2:

Show value

Screen:

By pressing the button:

add favourite

an overview of available values
will be displayed

Act. clear

the selected value can be
deleted

the second page of the main
menu will be displayed.

Load scheme

a default scheme gets loaded

Clear all

All values will be deleted

Boiler 000

the boiler values, which can be
selected

manually,

will

displayed

HOT WATER

TANK i000

the hot water tank values, which
can be selected manually, will
be displayed

Heating circuit

i002

the heating circuit values, which
can be selected manually, will
be displayed

SOLAR i003

the solar values which, can be
selected

manually

will,

displayed

BUFFER i004

the buffer values, which can be
selected

manually,

will

displayed

TIME MODE 000

the time mode values, which
can be selected manually, will
be displayed

other modules

Depending on the installation,
other modules can also be
displayed.

Summary of Contents for pelletfire 20/20





































































































Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands

Herz pelletfire 20/20, Operating Instructions Manual

Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands