Herz pelletfire 20/20 Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 100

Herz pelletfire 20/20 Operating Instructions Manual Download Page 20

8

Temperature manager

20

If the required buffer-top-temperature (required temperature) is higher than the sum of buffer-bottom-MUST-
temperature and the set difference, then the required boiler temperature is the result of the required buffer-
top-temperature (required temperature) + the adjusted temp. increase (see figure 8.2). Caution: Consider the

set minimum requirement

.

Figure 8.2: Example temperature manager with buffer and without difference

If  the  required  buffer-top-temperature  (required  temperature)  is  lower  than  the  buffer-bottom-MUST-
temperature  than  the  required  boiler  temperature  is  the  result  of  the  required  buffer-bottom-temperature  +
the  adjusted  temp.  increase  +  the  adjusted  difference (see  figure  8.3).  Caution:  Consider the  set  minimum
requirement.

Figure 8.3: Example temperature manager with buffer and difference

«
...
18
19
20
21
22
...
»

Summary of Contents for pelletfire 20/20





































































































Reviews:

No comments