Herz pelletfire 20/20 Page 25 Operating Instructions Manual Download | Manualshive

Page: 25 / 100

background image

Menu navigation and adjustment values

9

25

9.3.1

Operation and handling

The touch panel is a touch-sensitive screen and control unit. By touching the screen, you can change
released values or move to other pages. The screen navigation and input can be done with finger, pen,
pencil, etc.

9.4

Main menu

After start up, this picture will appear. In the centre of the screen important values according the boiler,
buffer, hot water tank, heating circuit and so on are shown. The shown values can be adapted individually.

NOTE: The values shown in the individual screenshots are not default values!

If the following symbol is pressed:

the main menu will be displayed. (Home Button)

you come back one level (return button)

fault messages (warnings & alarms) will be displayed

(see chapter

10

)

the individual modules (boiler, hot water tank, buffer, heating circuit,
solar, hydraulic compensator, net pump, zone valve, external demand)
will be displayed.

(see chapter 10)

the menu settings (network configuration, E-Mail, screen saver) will be
displayed

(see chapter 9.10)

the date & time can be set up

(see chapter 9.13)

the code input screen will be shown

(see chapter 9.7)

the boiler gets switched On / Off.

(see chapter 9.6)

can be switched between the pages of the value overview on the start
screen.

you get to the display of the current weather data.

«
...
23
24
25
26
27
...
»

Summary of Contents for pelletfire 20/20





































































































Reviews:

No comments

Related manuals for pelletfire 20/20

GO!control 2GIG-CNTRL2

Brand: 2gig Technologies Pages: 52

GO!control 2GIG-CNTRL2

Brand: 2gig Technologies Pages: 52

Brand: Badeloft Pages: 12

Brand: Jensen Pages: 2

Brand: Kärcher Pages: 60

Brand: WaterLogic Pages: 69

Brand: ADEMCO Pages: 56

Brand: Displays2go Pages: 3

Brand: Truweld Equipment Pages: 28

Brand: TradeQuip Pages: 9

kb sound Series

Brand: EIS Pages: 2

Brand: Mark Climate Pages: 60

Brand: Creative Pages: 10

Brand: Fender Pages: 14

Brand: Paton Pages: 17

Brand: Riello Pages: 2

Brand: Gladen Pages: 2

Brand: Quell Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands