Herz pelletfire 20/20 Page 44 Operating Instructions Manual Download

Page: 44 / 100

Menu navigation and adjustment values

Term

Description

Unit

Settings

Must temperature

Setting the must temperature (47-85) of the boiler

°C

Min. Temperature

Activate/setting the min. temperature (20-58) (ON/OFF)

▪

With activated min. Outside of the hot water tank loading time, the hot

water tank temperature is set to the set min. temperature loaded.

If the hot water tank temperature is below the value of the set min.
temperature, the hot water tank loading starts.

°C

Min. loading

Indicates/activates the min. loading (20-58) (ON/OFF)

▪

With activated min. Outside of the hot water tank loading time, the hot

water tank temperature is set to the set min.

If hot water tank temperature is lower than the min. loading / temperature
value, the hot water tank loading will start.

°C

Circulation
temperature*

Setting the circulation temperature of hot water tank

°C

Menu "Aggregate-Test"

Agg-Test

Hot water tank pump*

If the indicator light lights, the output for controlling of the hot water tank
pump is switched.

Loading valve

If the indicator light lights, the output for controlling of the loading valve is
switched.

Circulation pump

Indicates the state of the hot water tank pump:
If the indicator lamp lights up, the hot water tank pump is activated and
the hot water tank gets charged.

Menu "time program / barrier times / circulation times“

Time program

1 2 3

Time 1

1 - 3 times can be set. The second and third time can be added by the
+. Example:

▪

time 1:

08:00

– 10:00

▪

time 2:

15:00

– 21:00

▪

time 3:

00:00

– 00:00

08:00

– 11:00

Setting up individual hot water tank loading times of every weekday

By pressing the symbol Monday preset gets assigned to remaining
weekdays

Barrier times

4 5

Time 1

1 - 2 times can be set. The second time can be added by the +.
Example: see time program

08:00

– 11:00

Setting up individual hot water tank loading times of every weekday,
when it will be not heated

By pressing the symbol Monday preset gets assigned to remaining
weekdays.

Circulation time

6 7 8

Time 1

1 - 3 times can be set. The second time can be added by the +.
Example: see time program

08:00

– 11:00

Setting up individual hot water tank loading times of every weekday,
when the hot water tank circulates.

By pressing the symbol Monday preset gets assigned to remaining
weekdays.

Summary of Contents for pelletfire 20/20





































































































Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands

Herz pelletfire 20/20, Operating Instructions Manual

Search results

Summary of Contents for pelletfire 20/20

Reviews:

Related manuals for pelletfire 20/20

Brands by name

Popular brands